Phoenix and SmartMouse

Phoenix interface

phoenix.bmp - PCB of the Phoenix interface
phoenixo.bmp - layout of components of the Phoenix interface

It is an interface used for communication a PC with a smartcard (original as well as pirate). The Phoenix interface can also be used to update the EEPROM 24(L)C16 on the Multimac II cards (gold wafer cards). This interface require a separate power supply (9 - 30V). Connection with the PC serial port is made by cable 1-1, 9pin connectors, male-female.

Basic schematic diagram:
-------------------------

              +-------------+  +
  +-----------|1     V    16|---+---o +5V (VCC)
 +|          +|             |  ===
 === +5V o-||-|2  MAX232  15|---+---o GND 
  |           |             |
  +-----------|3      +---14|-               +5V (VCC)  +-<-o DTR
           +  |       |     |                   o       |
     +---||---|4      | +-13|----o RTS          |       +->-o DSR
     |        |       | v   |                   /       |
     +--------|5      | +-12|----o RST          \ 22K   +->-o CTS
          +   |       |     |                   /
     GND o-||-|6      +-<-11|-                  \
              |             |                   |
     RxD o----|7  ---<--- 10|-------------------+----o I/O
              |             |              |\   |
     TxD o----|8  --->---  9|--------------| |--+
              +-------------+             1|/ 2
                                          74LS07
    At the MAX232, pin 2 delivers
    +10 V and pin 6 delivers -10 V.        74LS07
                                           pin 7=GND, pin 14=VCC



     1M         2.2k        3|\4
  +-/\/\/--+----/\/\/-----+--| o-----+-------------o CLK
  |        |2             |  |/      |
  |       -o-             |          |100 pF
  |     /_____\           |         ===
  |        |1             |          |
  |        | 3.579545 MHz |          |
  |        |     +--+     |          -      74HC04
  +--------+---| |  | |---+         GND     pin 5,7,9,11,13=GND,
           |     +--+     |                 pin 14=VCC=+5 V
           |27pF          |27pF
          ===            ===
           |              |
           -              -
          GND            GND

List of components:
-------------------
1 x slot for ISO card (eight pins are enough)
1 x female 9pin connector RS232
1 x MAX232
1 x 7805 (78L05)
1 x 74LS07 (7407)
1 x 74HC04
1 x LED green
1 x LED red
5 x capacitor 4u7/16V (2u2-22u/16-63V)
1 x capacitor 100nF
1 x capacitor 100pF
2 x capacitor 27pF
2 x resistor 220R
2 x resistor 2K2
1 x resistor 22K
1 x resistor 1M0
1 x crystal 3.579545 MHz

SmartMouse

Two version of SmartMouse are presented - (A) and (B).

(A) without data LED and protective resistors.

(B) with LED and protective resistors.

smouse.bmp -  PCB of SmartMouse
smouseo1.bmp - layout of components of version A
smouseo2.bmp - layout of components of version B
smouses1.bmp - schematic diagram of version A
smouses2.bmp - schematic diagram of version B

The  interface can also be used as Phoenix to update the EEPROM 24(L)C16 on the Multimac II cards (gold wafer cards) or as SmartMouse to update original Irdeto cards. This interface require a separate power supply (9 - 30V). Connection with the PC serial port is made by cable 1-1, 9pin connectors, male-female.

List of components - SmartMouse A:
--------------------------------------
4 x capacitor 22pF
1 x capacitor 47pF
3 x capacitor 100nF
5 x capacitor 2,2uF/16V (1uF-22uF/16-63V)
4 x resistor 2K2
1 x resistor 10K
2 x resistor 1M0
1 x 1N4148
1 x BAT41 or BAT48, Shottky!!
1 x green LED, 3mm "Low Power"
1 x 74HC00
1 x MAX 232
1 x 78L05
2 x single switch on-on
1 x female 9pin connector RS232
1 x slot for ISO card (eight pins are enough)
1 x crystal 3.579545 MHz
1 x crystal 6MHz

List of components - SmartMouse B:
--------------------------------------
4 x capacitor 22pF
1 x capacitor 47pF
3 x capacitor 100nF
5 x capacitor 4,7uF/16V (1uF-22uF/16-63V)
1 x resistor 10R
3 x resistor 100R
4 x resistor 1K0
2 x resistor 2K2
1 x resistor 4K7
2 x resistor 1M0
1 x 1N4148
1 x BAT41 or BAT48, Shottky!!
3 x green LED,  3mm "Low Power"
1 x 74HC00
1 x MAX 232
1 x 78L05
2 x single switch on-on
1 x female 9pin connector RS232
1 x slot for ISO card (eight pins are enough)
1 x crystal 3.579545 MHz
1 x crystal  6MHz

SmartMouseB - version "SATHACK.cz"

SimplePhoenix

It is a simple variant of SmartMouse which can be used as Phoenix interface. This SimplePhoenix together with StupidPipo and Jupiter Card programmer is able to program Gold Wafer Cards, Jupiter Cards and Fun Cards.

simplephoenix.bmp -  PCB of SimplePhoenix
simplephoenixo.bmp - layout of components
simplephoenixs.bmp - schematic diagram

This interface require a separate power supply (9 - 30V). Connection with the PC serial port is made by cable 1-1, 9pin connectors, male-female.

List of components
-------------------
2 x capacitor 22pF
1 x capacitor 47pF
3 x capacitor 100nF
5 x capacitor 4,7uF/16V (1uF-22uF/16-63V)
2 x resistor 1K0
1 x resistor 2K2
1 x resistor 10K
2 x resistor 1M0
1 x 1N4148
1 x BAT41 or BAT48, Shottky!!
2 x green LED,  3mm "Low Power"
1 x 74HC00
1 x MAX 232
1 x 78L05
1 x female 9pin connector RS232
1 x slot for ISO card (eight pins are enough)
1 x crystal 3.579545 MHz

Download PACKET_D (198k)

Content of Packet_d:

• info_d.htm - this page,
• phoenix.bmp - PCB of the Phoenix interface,
• phoenixo.bmp - layout of components of the Phoenix interface,
• smouse.bmp -  PCB of SmartMouse,
• smouseo1.bmp - layout of components of version A,
• smouseo2.bmp - layout of components of version B,
• smouses1.bmp - schematic diagram of version A,
• smouses2.bmp - schematic diagram of version B,
• simplephoenix.bmp -  PCB of SimplePhoenix,
• simplephoenixo.bmp - layout of components,
• simplephoenixs.bmp - schematic diagram.

HOME E-MAIL