Programmers for FunCard
In this page programmers for FunCard and processors AT90S8515 are described.
FunCard programmer ver.1.1 A
This programmer is the same as the FunCard programmer ver.1.1 from www.funcard.net. The parallel port of PC is used for connection.
fcproga.bmp - PCB of
FunCard programmer ver.1.1 A - standard Centronix printer connector or Cannon 25-male can
be used,
fcprogas.bmp - schematic
diagram of FunCard programmer ver.1.1 A (from www.funcard.net),
fcprogao.bmp - layout of
components of FunCard programmer ver.1.1 A.
FunCard programmer ver.1.1 A - version "SATHACK.cz"
List of components:
1 x slot for ISO card (eight pins are enough)
1 x female Centronix connector 36pin or Cannon 25-male
1 x Zener diode 5,1V
1 x LED green
1 x capacitor 4u7/16V
3 x resistor 220R
1 x resistor 470R
1 x socket 20pin
1 x socket 40pin
This programmer is the same as the FunCard programmer ver.1.2 from www.funcard.net. The parallel port of PC is used for connection. This programmer is better then the ver.1.1 when using long cable or when the ver.1.1 doesn't work correctly.
fcprog2a.bmp - PCB of
FunCard programmer ver.1.2 A - standard Centronix printer connector or Cannon 25-male can
be used,
fcprog2as.bmp - schematic
diagram of FunCard programmer ver.1.2 A (from www.funcard.net),
fcprog2ao.bmp - layout of
components of FunCard programmer ver.1.2 A.
List of components:
1 x slot for ISO card (eight pins are enough)
1 x female Centronix connector 36pin or Cannon 25-male
2 x 74HC14
1 x Zener diode 5,1V
1 x LED green
1 x capacitor 4u7/16V
3 x resistor 100R
1 x resistor 470R
1 x socket 20pin
1 x socket 40pin
FunCard fuse programmer (fully tested now)
There are a few changes around 7812 regulator in comparison with the previous version .
fcfuseprog.bmp - PCB of
FunCard fuse programmer - standard Centronix printer connector or Cannon 25-male can be
used,
fcfuseprogs.bmp - schematic
diagram*) of
FunCard fuse programmer,
fcfuseprogo.bmp - layout of
components of FunCard fuse programmer,
win_fbe.zip - FuseBitEditor*) - software for
programming AT90S1200 and AT90S2313 (AT90S8515).
Setting of FuseProgEditor to activate SPIEN and FSTRT bits - right setting for FunCard. Setting of FuseProgEditor to deactivate SPIEN and FSTRT bits.
*) FunCard fuse programmer is based on FuseBit-Editor from G.Mueller. The homepage of this project is in http://uc-project.de.
The parallel port of PC is used for connection. Programmer requires a separate power supply (17 - 30V DC).
List of components:
1 x female Centronix connector 36pin or Cannon 25-male
1 x 74HC240
1 x 4094
1 x 78L05 (7805)
1 x 7812
1 x PNP transistor BC 327, BC328
1 x NPN transistor BC 337, BC547 C
1 x 1N4001
2 x 1N4148
1 x LED green, 3mm "Low Power"
1 x capacitor 22u/25-63V - depend on power supply
4 x capacitor 100nF
1 x resistor 1K0
2 x resistor 4K7
1 x resistor 1M0
1 x socket 20pin
1 x socket 40pin
Fuseprogrammer by Andrzej
On the http://www.ksw.hg.pl/ you can find Fuseprogrammer by Andrzej.
fuseprog_andrzej.bmp - PCB of
Fuseprogrammer by Andrzej - standard Centronix printer connector or Cannon 25-male can be
used,
fuseprog_andrzejs.bmp - schematic
diagram of Fuseprogrammer by Andrzej,
fuseprog_andrzejo.bmp - layout of
components of Fuseprogrammer by Andrzej,
fuse.zip - AC fuse prog - software for programming AT90S8515 by Andrzej.
The parallel port of PC is used for connection. Programmer requires a separate power supply (17 - 30V DC).
Setting of FuseProgEditor to activate SPIEN and FSTRT bits - right setting for FunCard. Setting of FuseProgEditor to deactivate SPIEN and FSTRT bits.
List of components:
1 x female Centronix connector 36pin or Cannon 25-male
1 x 78L05 (7805)
1 x 7812
2 x NPN transistor BC 337, BC547 C
1 x 1N4001
2 x 1N4148
1 x LED green, 3mm "Low Power"
1 x capacitor 22u/25-63V - depend on power supply
4 x capacitor 100nF
1 x resistor 1K0
3 x resistor 4K7
1 x socket 40pin
PROPG ATmega
There is other programmer for AVR processors in www.mite.cz and it is PROG ATmega.
ATMEL AV programer
The third one - Kit122 - ATMEL AV programmer in kitsrus.com .
Content of Packet_p:
- info_p.htm - this page,
- fcproga.bmp - PCB of FunCard programmer ver.1.1 A,
- fcprogas.bmp - schematic diagram of FunCard programmer ver.1.1 A,
- fcprogao.bmp - layout of components of FunCard programmer ver.1.1 A,
- fcprog2a.bmp - PCB of FunCard programmer ver.1.2 A,
- fcprog2as.bmp - schematic diagram of FunCard programmer ver.1.2 A,
- fcprog2ao.bmp - layout of components of FunCard programmer ver.1.2 A,
- fcfuseprog.bmp - PCB of FunCard fuse programmer,
- fcfuseprogs.bmp - schematic diagram of FunCard fuse programmer,
- fcfuseprogo.bmp - layout of components of FunCard fuse programmer,
- fuseprog_andrzej.bmp - PCB of Fuseprogrammer by Andrzej,
- fuseprog_andrzejs.bmp - schematic diagram of Fuseprogrammer by Andrzej,
- fuseprog_andrzejo.bmp - layout of components of Fuseprogrammer by Andrzej,
- win_fbe.zip - FuseBitEditor for 90S1200 and 90S2313 (90S8515),
- fuse.zip - AC fuse prog - software for programming AT90S8515 by Andrzej.
